Axalta - Imprimación blanca Tufcote Hydro 1262
Mejor vendido

Axalta - Imprimación blanca Tufcote Hydro 1262

Tufcote Hydro 2.1 PR es una imprimación acrílica al agua, de secado rápido y bajo en COV, diseñada con excelentes propiedades de adhesión para una amplia variedad de sustratos metálicos y productos de madera. Esta imprimación es una excelente opción para áreas que requieren una imprimación sin plomo ni cromatos. La imprimación blanca 1262 ha sido aprobada por el USDA como imprimación para áreas sujetas a contacto accidental con alimentos.

Choose your location

enter a US zip code

Más información

Especificación del producto

Tufcote Hydro 2.1 PR is a waterborne low VOC, quick-dry, acrylic based primer designed with excellent adhesion properties for a wide variety of metal substrates and wood products. This primer is an excellent choice for areas that require a primer that contains no lead or chromates. 1263 Gray Primer has been USDA approved as a primer in areas subjected to incidental food contact.

Works well as an economy coating on properly prepared metal and wood where the following attributes are desired:

  • Fast drying
  • Water reducible
  • Non-flammable
  • Corrosion resistant
  • Good flexibility
  • Easy application
  • For the coating of metal parts and products
  • Meets clean air standards
  • Outstanding adhesion

SURFACE PREPARATION

All surfaces to be painted must be clean, dry and in fit condition to be painted. Be sure to remove all wax, silicone, oil, powdery or scaling rust, loose or peeling paint and all other foreign matter. Smooth, slick surfaces should be sanded to promote adhesion. Prime bare and uncoated surfaces with Tufcote Primer.

BARE FERROUS METALS: Clean off all dirt, grease, oil, wax or other foreign matter. All loose, powdery or scaling rust must also be removed. A completely de-rusted surface is recommended. Prime bare and uncoated surfaces with Tufcote Primer.

For best results on steel, abrasive blast surface to an SSPC-SP-6 Commercial Blast. Profile should be 2.0 to 2.5 mils. Average peak to valley surface profile shall be 1.5 to 2.5 mils. If blasting is not possible or practical, hand tool clean to an SSPC-SP 2 or power tool clean to an SSPC-SP 3 may be used with sacrifice in performance vs. blasted surfaces.

Aluminum surfaces should be properly treated. Surface preparations may include sanding, brush off blasting (SSPC-SP7), alodine treatment, treatment with an acid, or other preparation necessary to ensure adhesion. All aluminums are not alike, it is strongly suggested that adhesion testing be done to assure system robustness.

Galvanized steel surface preparation may include detergent washing, pre-treatment and abrasion for new surfaces; for weathered surfaces, detergent washing and sanding. For new galvanized surfaces, acid treatments, degreasing and abrasion might be required before application of appropriate primer.

PAINTED SURFACES: Be sure all loose and peeling paint is completely removed, and the surface is clean. Remove excess chalkiness with a wire brush or by sanding. Feather edge and spot prime with Tufcote Primer.

WOOD SURFACES: Clean wood thoroughly. Prime and seal with one coat of Tufcote Primer or Tufcote Hydro.

APPLICATION

Apply 1 to 2 coats at package consistency. Allow primer to dry for 1 hour, then apply topcoat using conventional application methods and equipment.

También te puede interesar

Décadas de experiencia

Desde 1993, nos hemos dedicado a ofrecer productos de alta calidad y un servicio excepcional.

Envío rápido

Los artículos en stock se envían el mismo día si se compran antes de las 11 a. m., hora del Este.

Servicio al cliente

Estamos aquí de lunes a viernes, de 8 a. m. a 5 p. m., para ayudarlo con su pedido y responder cualquier pregunta.

Pago seguro

Utilizamos un sistema encriptado, compatible con PCI y con protección contra fraude para mantener sus transacciones seguras.